Welbilt Lincoln Impinger 1600 Series International Service Manual Download

Page: 10 / 52

Document #: LIN_GO_SM_IMPLOPRO_S1600_INTL_4605727 – 9/20

Installation

Section 2

Canopy Ventilation Recommendations

NOTE: Hood shown as dimensional for island mount. Size reductions may be possible for wall mount units.

CAPTURE AREA

78"

(1981 mm)

AFF MAX

120"

(3048 mm)

22"

(559 mm)

18 - 24"

(457 - 609 mm)

22"

(559 mm)

CAPTURE VELOCITY

CAPTURE

VELOCITY

80"

(2032 mm)

12"

(305 mm)

12"

(305 mm)

AFF = Above Finished Floor

NOTE: The drawing shown is a typical installation and is

intended to be a guideline. It is not a rigid specification.

Hood dimensions and the positioning of the hood over the

oven will vary with hood manufacturers.

NOTE: Lincoln can provide oven spec sheets that show

the dimensions of the oven, kW or BTU ratings and other

information that will be useful to both the ventilation hood

supplier and the HVAC contractor.

Summary of Contents for Lincoln Impinger 1600 Series





















































Search results

Summary of Contents for Lincoln Impinger 1600 Series

Reviews:

Related manuals for Lincoln Impinger 1600 Series

Brands by name

Popular brands

Welbilt Lincoln Impinger 1600 Series, International Service Manual

Search results

Summary of Contents for Lincoln Impinger 1600 Series

Reviews:

Related manuals for Lincoln Impinger 1600 Series

Brands by name

Popular brands