manualshive.com logo in svg

Weishaupt W-FM 25, Manual

Share
Download
Weishaupt W-FM 25 Manual Download Page 6

1.2 Guarantee and Liability

Guarantee and liability claims for personal and equipment damage are excluded, if

they can be attributed to one or more of the following causes:

▪

Non approved application,

▪

non-observance of the installation and operating instruction,

▪

operation with faulty safety equipment,

▪

continual operation despite a fault,

▪

improper installation, commissioning, operation and service,

▪

unauthorised modifications made to the unit,

▪

the installation of additional components, which have not been tested with the unit,

▪

the installation of combustion chamber inserts, which impede full flame formation,

▪

repairs, which have been carried out incorrectly,

▪

the use of non original Weishaupt parts,

▪

unsuitable fuels,

▪

defects in the inlet lines,

▪

acts of God.

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

1 User instructions

83294002 • 2/2014-11 • La

6-70

Summary of Contents for W-FM 25









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands