manualshive.com logo in svg

Weishaupt W-FM 25, Manual

Share
Download
Weishaupt W-FM 25 Manual Download Page 37

6.2 Gas burner with speed control

1. Preset combustion manager

▶

Unplug plug No. 7 from combustion manager.

▶

Switch on voltage supply.

✓

The unprogrammed condition of the combustion manager is indicated by a flashing

display.

The burner goes to lockout.

▶

Press [ENTER] key.

✓

Burner has been reset.

✓

Combustion manager drives to Standby.

Parameter 

A

 must be set to value

2

.

▶

Press [Enter] and [+] keys simultaneously for approx. 2 seconds.

✓

The parameter level is activated.

▶

Press [+].

▶

Press [Enter] key until parameter 

A

 is displayed.

▶

Set parameter 

A

 to value 

2

 (without low gas pressure switch).

▶

Press [Enter] key until parameter 

OFFUPr

 is displayed again.

▶

Press [G] and [L/A] simultaneously.

✓

Combustion manager changes to access level.

▶

Press [+].

✓

Setting level (parameter 

E0

) is displayed.

▶

Adopt value 

0

 (single fuel burner), if necessary adjust using [ENTER] and [-] key.

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

6 Commissioning

83294002 • 2/2014-11 • La

37-70

Summary of Contents for W-FM 25









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands