manualshive.com logo in svg

Weishaupt W-FM 25, Manual

Share
Download
Weishaupt W-FM 25 Manual Download Page 53

▶

Adopt value 

0

 (intermittent operation) using [+] key.

✓

E2

 is displayed.

▶

Adopt value 

0

 (flame sensor FLW), if necessary set using [ENTER] and [-] key.

▶

Press [+].

✓

E3

 is displayed.

▶

Adopt value 

1

 (fan control), if necessary set using [ENTER] and [-] or [+] key.

▶

Press [+].

✓

Combustion manager changes into the setting level for step points.

▶

Determine the air damper setting for operating points P

9

, P

1

 P

0

and P

2

 from the

sticker for burner setting.

The operating points are preset using these values:

▶

Press [+].

✓

Factory setting operating point P

9

 (Full load) is displayed.

▶

Press and hold [L/A] and set air damper setting using the [–] or [+] key.

▶

Press [+].

✓

Factory setting operating point P

1

 (stage 1) is displayed.

▶

Press and hold [L/A] and set air damper setting using the [–] or [+] key.

▶

Press [+].

✓

Factory setting operating point P

9

 (ignition position) is displayed.

▶

Press and hold [L/A] and set air damper setting using the [–] or [+] key.

Installation and operating instruction

Replacing combustion manager W-FM 20 … 24 with W-FM 25

6 Commissioning

83294002 • 2/2014-11 • La

53-70

Summary of Contents for W-FM 25









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands