background image

4

Upright

Adjustment Tube

Backrest

Curl Pad

Weight Rest

Storage Tube

Right Side

Left Side

Note: The terms “right side” and “left side” are determined
relative to a person sitting on the weight bench; they do not
correspond to right and left on the drawings in the manual.

Leg Lever

Olympic Adapter

Seat

BEFORE YOU BEGIN

Thank you for selecting the versatile WEIDER

®

CLUB

weight bench. The weight bench offers a selection of
weight stations designed to develop every major mus-
cle group of the body. Whether your goal is to tone
your body, build dramatic muscle size and strength, or
improve your cardiovascular system, the weight bench
will help you to achieve the specific results you want.     

For your benefit, read this manual carefully before
using the weight bench. 

If you have questions after

reading this manual, please see the front cover of this
manual. To help us assist you, note the product model

number and serial number before contacting us. The
model number is WEBE1066.0. The serial number can
be found on a decal attached to the weight bench (see
the front cover of this manual).

To avoid a registration fee for any service needed
under warranty, you must register the weight bench
at www.weiderservice.com/registration.

Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.

ASSEMBLED DIMENSIONS: 
Height: 61 in. / 155 cm
Width: 42 in. / 107 cm
Depth: 60 in. / 152 cm

Summary of Contents for CLUB WEBE10660.0





















Reviews: