Weco HeSU 4k4 PRO Installation Manual Download Page 40

Page: 40 / 46

WeCo Srl Italia

www.wecobatteries.com

[email protected]

4K4 PRO V 1.11 28-9-2021

8.4

To set the CAN protocol to match the inverters communication protocol, select the inverter that you are connecting to

from the list and press SET, wait for the positive feedback after the first communication with the inverter

Using the Software available on> https://wecobatteries.com/download-area

8.5

The normal mode for equalization is Auto mode, however in the unlikely event of a failure it is possible to perform a

manual equalization. If it is necessary to perform a manual equalization, please contact WeCo support for further

advice. Reference to the CELL EQUALIZATION MANUAL (not public) will be necessary to activate the manual procedure.

IMPORTANT After the first Manual/Forced Equalization the single cell equalizer will return to Auto mode within 24h.

Summary of Contents for HeSU 4k4 PRO















































Search results

Summary of Contents for HeSU 4k4 PRO

Reviews:

Related manuals for HeSU 4k4 PRO

Brands by name

Popular brands

Weco HeSU 4k4 PRO, Installation Manual

Search results

Summary of Contents for HeSU 4k4 PRO

Reviews:

Related manuals for HeSU 4k4 PRO

Brands by name

Popular brands