background image

Chapter 2 

Safety regulations 

 

40001136 Geset 125

 

Version: 30.07.14

 

Page 13 of 57  

GB

 

Reasonably foreseeable misuse 

Usage different than or going beyond that specified under "Intended use" is considered 
unauthorized. 

The operator bears sole responsibility for 

  Damage arising from improper use. 

  Furthermore, the manufacturer assumes no liability for such use. 

 

Improper use can cause exposure to risk! 

 

Improper use includes e.g. the following: 

  Operating in an explosive atmosphere 

  When the labeling system comes into contact with food… 

 

 
 
 

Modifications and alterations to the labeling station 

If the machine is independently modified and altered, all of the manufacturer's liability and 
warranties will expire. This also holds true for modifications and changes to the programs 
of the programmable control system as well as changes to the parameters to control 
devices not described in these operating instructions. 

The electromagnetic behavior of the machine can be impaired by additions or changes. 

Do not change or modify the machine without first consulting the manufacturer and 
obtaining the written approval. 

Summary of Contents for Geset 125


























































Reviews: