background image

Transportation and storage | 4

5111232A OI-II Webasto Next

7 / 23

3.3

Description of power supply interface
connections

The connections of the mains cable are marked with "IN". The 5
terminals on the left have L1/L2/L3/N/PE printed on them
The connections of the charging cable are marked with "OUT".
The 5 terminals on the right have PE/N/L1/L2/L3 printed on
them

NOTE

To release the power supply connections, use an insu-
lated flat-head screwdriver by inserting it into the open-
ing for this purpose immediately above push-in ter-
minal.

L3 L2 L1 N

PE PE

N L1 L2 L3

18 mm

L3/IN

L2/IN

L1/IN

N/IN

PE

PE

N/OUT L1/OUT L2/OUT L3/OUT

IN

OUT

230 - 400 VAC

Fig. 4

IN

Power cable connections

OUT

Charging cable connections

4

Transportation and storage

Observe the ambient temperature for storage during transporta-
tion. See chapter 17, "Technical data" on page 20.
Transport the charging station only when suitably packaged.

5

Scope of delivery

Scope of delivery

Amount

Charging station

1

Charging cable with charging coupling

1

Installation kit for wall mounting

l

Wall plug (8 x 50 mm, Fischer UX R 8)

4

l

Screw (6 x 70, T25)

2

l

Screw (6 x 90, T25)

2

l

Washer (12 x 6.4 mm, DIN 125-A2)

4

l

Screw (3 x 20 mm, T10); (2 replacement
screws)

2

l

Mounting bracket

1

l

Cable bushing, (one is custom-made)

2

Installation kit for charging cable:

l

Spiral antikink protection

1

l

Cable tie

1

l

Strain relief clamp

1

l

Screw (6.5 x 25 mm, T25) for fastening the
strain relief clamp

2

"Important Information on Operating and Installa-
tion Instructions"

1

"Scan & Charge" QR codes

2

NOTE

The Fischer universal wall plug UX R 8 supplied is a
plastic wall plug made of high quality nylon. The univer-
sal wall plug splays out in solid building materials and
catches in wooden and board materials for excellent re-
tention.

6

Required tools

Tool description

Amount

Slot-head screwdriver 0.5x3.5 mm

1

Torx screwdriver Tx25

1

Torx screwdriver Tx10

1

Torque wrench (range covers 5-6 Nm, for Tx25)

1

Torque wrench (range covers 4-5 Nm, for open-
ended spanner size 29)

1

Drilling machine with 8 mm drill

1

Hammer

1

Measuring tape

1

Spirit level

1

Wire stripping tool

1

Installation tester

1

EV simulator with rotary field display

1

Round file

1

Combination pliers

1

NOTE

A drill template, which likewise forms part of the scope
of delivery, is also available to print out. It must be prin-
ted on a 1:1 scale. Check the dimensions after printing.

Summary of Contents for Next
























Reviews: