background image

Installation and electrical connection | 8

5111232A OI-II Webasto Next

13 / 23

8.5

LAN cable

For connecting the charging station to the network infrastruc-
ture at the installation location. The charging station can be
configured and controlled using this connection (prerequisite:
connection to the back end or to the local energy management
system). A CAT 7 network cable or higher is recommended. The
LAN cable must be passed through the left-hand opening in the
wall box in order to connect it to the LAN socket.

8.6

Active power increase

4
3
2
1

Fig. 9

The active power control as per the rules of VDE AR-4100
should be connected as follows:
The two cables from the ripple control receiver must be inserted
into this connector in positions 3 and 4 (see Fig. 9). The two
cables can be assigned to pos. 3 and 4 in any order. (max. cable
cross section 1.5 mm²).

8.7

DIP switch settings

DANGER

High voltages.

u

Danger of fatal electric shock.

u

Ensure safe isolation from the power supply.

DIP-switches configure the current setting of the charging sta-
tion.
DIP switches determine the maximum current. The current can
be adjusted in 1 A increments using the Charger Setup app up
to the maximum value that is configured by the DIP switch.

ON (1)

OFF (0)

Fig. 10

DIP switch left/ON = 1
DIP switch right/OFF = 0
DIP-switch factory setting:

D1

D2

D3

D4

D5

D6

Off

Off

Off

On

On

On

NOTE

Changes to the DIP switch settings become active after
restarting the charging station.

The DIP switches should be programmed in such a way that the
output power illustrated below for the single- and three-phase
charging operation can be set to the desired maximum current
(D1-D6).

D1

D2

D3

[A]

Description

0

0

0

32

Factory settings

0

0

1

10

0

1

0

13

0

1

1

16

1

0

0

20

1

0

1

25

1

1

0

8

1

1

1

0

Demo mode: charging not pos-
sible

D4

0=

no unbalance load limit for single-phase char-
ging.

1=

unbalance load limit at 16 A and D1-D3 > 20 A
(for CH and AT).

D5

0=

no unbalance load limit for single-phase char-
ging.

1=

unbalance load limit at 20 A and D1-D3 > 25 A
(for D).

D6

1=

TN/TT system.

0=

IT system (only single-phase connection pos-
sible).

Summary of Contents for Next
























Reviews: