background image

 

DECAL LOCATION DIAGRAM 

 

 

 

Nameplate 

 

Note: The following information coming from the nameplate.

 

The nameplate is stuck in  the center to the  top on the rear  of the machine. The meaning  of 

each part is in the following

 

 

CB     

9XX

    B   

 

 

                              With hood 

 

                              Model 

                                    Computerized dynamic wheel    balancer   

B. CE certificate           

 

This mark indicates that this model of machine has got the CE certificate 

 

C

Series  No  The  first  3numbers  is  the  abbreviate  of  the  model.  The  middle  4  is  the 

manufacture date and the last 4 is company product series number. 

D

What on the cross line is the name and address of the company and under the cross line 

not  includes  the  above  explained  but  the  rated  electrical  parameters,  such  as  voltage

frequency

power

phase number & full load current, and the weight and manufacture date of 

the machine. 

 

If the B has noted in the model of the machine, it means the machine with the protection cover. 

It means without the equipment of the protection cover if without the note of B.   

 

 

 

Summary of Contents for W-957-40











































Reviews: