manualshive.com logo in svg

WBM KOMATSU GD655-6, Manual, Page: 34 / 82

Share
Download
WBM KOMATSU GD655-6 Manual Download Page 34

Weldco-Beales Manufacturing 

Page 34

WBM

MSW102 SNOW WING

PARTS, SERVICE AND INSTALLATION

ASSEMBLY AND INSTALLATION

INSTALLATION INSPECTION

FACTORY WORK LIGHT 

WIRING HARNESS

RIGHT SIDE

RIGHT SIDE LADDER 

SPACER MOUNT

3. Check that the “do not articulate when snow wing is in the transport or stowed 

position” warning decal is permanently affixed in the cab.

4. Check for proper clearances of components through full range of operation. 
5. Install ladder on ladder spacer.

6. Re-install the work light. Use the WBM provided work light wiring harness extension to 

reconnect the right side work light to the factory work light wiring harness. See photo 

below.

Installation Inspection

1. Check all bolts, all hose fittings and all connections for tightness.
2. Check that the position of the rear stop assembly will make contact with the 

pushpole, while in the transport position. Ensure the DEF tank access door can be 

fully opened and is not obstructed. If not already completed, fully weld the stop 

assembly on the rear mount.

Summary of Contents for KOMATSU GD655-6



















































































Reviews:

No comments