manualshive.com logo in svg

Wave NCBSLXE2, Installation And Operation User Manual

Share
Download
Wave NCBSLXE2 Installation And Operation User Manual Download Page 87

SPEEDLAN Installation and Operation User Guide

     

IP-Router Setup

8-5

                                                                                                                                                              

More Button - RIP Routing 

Click this button on the IP Router Setup dialog box to enable RIP.  Wave Wireless brouters support 
what is known as RIP (Routing Information Protocol). RIP allows users to permit network equipment to 
communicate with each other to handle the routing plan of your network.  Select the appropriate 
check boxes as described below:

•

 

Send RIP Default Route

Enabling this feature instructs the brouter to inform the network (via RIP) that it is the default 
router for that network. 

This feature should only be enabled if this brouter is the only 

default router on the local network. 

•

Send RIP Routes

Enabling this feature instructs the brouter to forward all route information gathered and 
stored by this brouter through the interface(s) selected. This is normally used in conjunction 
with Listen to RIP which instructs the brouter to gather RIP information from other RIP devices 
on your network. 

Summary of Contents for NCBSLXE2
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands