manualshive.com logo in svg

Wave NCBSLXE2, Installation And Operation User Manual

Share
Download
Wave NCBSLXE2 Installation And Operation User Manual Download Page 10

SPEEDLAN Installation and Operation User Guide

 

1-4

Introduction

Features  

•

10/100BASE-T Ethernet Interface 

•

SPEEDLAN 11 Mb Wireless Radio Interface 

•

Bridging Features 

•

Protocol Transparent Bridging 

•

IP Routing

•

Filtering by Ethernet Multicast, Broadcast and Bad Packets 

•

Filtering by Protocol 

•

Filtering by Ethernet Address Pair 

•

Generic Ethernet Tunneling through IP Networks

•

Learned Table Lockdown 

•

Expanded IP ARP Support 

•

Automatic Broadcast Storm Protection and Notification 

•

Supports up to 48 Remote Buildings

SNMP Features 

•

IP "ping" Support 

•

IP SNMP Support (MIB II, Ethernet, Interface, SNMP, and Bridge MIB) 

•

IP SNMP WaveLAN 

•

IP SNMP Trap Support 

•

SNMP Access Lists 

ISP Features

•

DHCP Server

•

Outgoing and Incoming NAT

SNMP Management 

SNMP wireless and wired link management may be administered from any Ethernet network or 
remotely from the Internet. The SNMP MIB II, Bridge MIB, and Ethernet-Interface MIB come with the 

Summary of Contents for NCBSLXE2
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands