manualshive.com logo in svg

Wave NCBSLXE2, Installation And Operation User Manual

Share
Download
Wave NCBSLXE2 Installation And Operation User Manual Download Page 84

SPEEDLAN Installation and Operation User Guide

 

8-2

IP-Router Setup

IP Routing Setup

IP Routing

 in the General Setup dialog box must be enabled for this dialog box to appear. Then, 

choose 

IP Routing Setup

 from the 

Setup

 menu on the SPEEDLAN Configurator. This dialog box 

must be completed before saving any configuration in which IP Routing has been enabled. 

Saving 

the configuration with incomplete entries in the route table will render the SPEEDLAN  
inoperable. 

Enter the appropriate information as described below:

•

Default Router (IP Address)

This entry should be set to the IP address of the default router that the SPEEDLAN is to use 
when it does not know where to route a particular IP packet.  

•

Default Router Interface

This entry should be set to the interface to which the default router is connected.   

•

Preferred IP Address

From time to time routers will transmit unsolicited IP packets such as SNMP Traps, Syslog, 
RIP, or IP ARP packets. Most routers randomly use one of the IP addresses from one of the 
router's interfaces as the source IP address for these packets. On the brouter you can specify 
the source IP address that you prefer to use for these packets.  

        
  
  
 

Summary of Contents for NCBSLXE2
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands