manualshive.com logo in svg

Wave NCBSLXE2, Installation And Operation User Manual

Share
Download
Wave NCBSLXE2 Installation And Operation User Manual Download Page 5

SPEEDLAN Installation and Operation User Guide

    

    Contents-3

Chapter 8 - IP-Router Setup ............................................................................ 8-1

IP Routing Setup.........................................................................................................................8-2

Add/Direct Button...............................................................................................................8-3
Add/Indirect Button.............................................................................................................8-4
More Button - RIP Routing ...................................................................................................8-5

Chapter 9 - SNMP Setup .................................................................................. 9-1

SNMP Setup ..............................................................................................................................9-2

Chapter 10 - System Access Setup .............................................................. 10-1

System Access Setup.................................................................................................................10-2

Chapter 11 - SNMP Monitoring ..................................................................... 11-1

Remote Statistics ......................................................................................................................11-2
Interface Monitor .....................................................................................................................11-5
Ethernet-like Interface Monitor...................................................................................................11-8
SectorPRC Station Entries ........................................................................................................11-10
11Mb RF Interface .................................................................................................................11-12
SNMP Monitor .......................................................................................................................11-14

SNMP Messages Received ...............................................................................................11-14
SNMP Messages Sent......................................................................................................11-16

IP Monitor .............................................................................................................................11-17
IP/TCP/UDP Monitor ..............................................................................................................11-20

TCP...............................................................................................................................11-20
UDP ..............................................................................................................................11-22

ICMP Monitor ........................................................................................................................11-23

ICMP Messages Received ................................................................................................11-23
ICMP Messages Sent.......................................................................................................11-24

Chapter 12 - Tables ........................................................................................ 12-1

System Information...................................................................................................................12-2
Bridge Learn Table ...................................................................................................................12-3
IP ARP Table ............................................................................................................................12-5
IP Route Table .........................................................................................................................12-7
IP/TCP Connection Table..........................................................................................................12-9
IP/UDP Listener Table.............................................................................................................12-10
Local IP-Address Table............................................................................................................12-11

Chapter 13 - Analyzing Wireless Equipment ............................................... 13-1

Select Another Device...............................................................................................................13-2
Analysis Polling Interval.............................................................................................................13-3
Wireless Link Test .....................................................................................................................13-3
Antenna Alignment...................................................................................................................13-8

Glossary......................................................................................................................... Glossary-1
Glossary of General Data Communications ...................................................................... Glossary-2

Summary of Contents for NCBSLXE2
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands