manualshive.com logo in svg

Wave NCBSLXE2, Installation And Operation User Manual

Share
Download
Wave NCBSLXE2 Installation And Operation User Manual Download Page 34

SPEEDLAN Installation and Operation User Guide

 

5-2

Configuring SPEEDLAN

General Setup    

This dialog box activates the features to configure your brouters. To select this dialog box, choose 

General Setup

 from the 

Setup

 menu of the SPEEDLAN Configurator. Select the appropriate check 

boxes as described below: 

•

Enable Bridging

The transparent bridging function will be enabled when this is item is selected. If you want 
the brouters to perform the bridging function, you must select this check box. When 
bridging is enabled, the Bridge Setup dialog box will be accessible. Bridging should be 
enabled for nearly all applications of the brouter. The default is ON.  

•

  

Enable IP Routing

The transparent routing function will be enabled when this is item is selected. IP Routing will 
work properly only if the routes are set up in the IP Route dialog box. 

If the routes are not 

set up properly before you save the configuration, the router will become 
inoperable.

 The default is OFF. 

  
  
  

        
  
  
 

Summary of Contents for NCBSLXE2
































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands