Wave NCBSLXE2 Installation And Operation User Manual Download Page 17

Page: 17 / 95

SPEEDLAN Installation and Operation User Guide

Quick Start

2-5

Step 4. Ground the Antenna

Mount the lightning arrestor to a solid surface.

Run the grounding wire from the lightning arrestor to a proper ground source such as a

grounding rod or roof ground wire.

Seal the entire lightning arrestor with the black waterproof sealant insulation putty that

comes in the installation kit.

Note:

The lightning arrestor is NOT

NOT

NOT waterproof.

Step 5. Connect the Wireless Bridge to the Power Supply

Make sure the switch on the power supply is set to the proper voltage (110V or 230V AC).

Connect the power cord’s IEC 320 female outlet to the IEC 320 male power inlet on the

back panel of the SPEEDLAN brouter.

Connect the power cord to an external power outlet (110V or 230V AC).

Step 6. Connect the Wireless Bridge to any Available Outlet of the Ethernet LAN

Connect the RJ-45 connector on a standard Ethernet cable to the RJ-45 port on the back

panel of the brouter.

Connect the other end of the Ethernet cable to your Ethernet hub, switch or router.

Step 7. Repeat If Needed

Repeat Steps 1-6 for all of the SPEEDLAN brouters that will be communicating with this one.

Summary of Contents for NCBSLXE2
































































































Search results

Summary of Contents for NCBSLXE2

Reviews:

Brands by name

Popular brands

Wave NCBSLXE2, Installation And Operation User Manual

Search results

Summary of Contents for NCBSLXE2

Reviews:

Brands by name

Popular brands