wattstopper CI-305 Installation Instructions Manual Download Page 2

UNIT DESCRIPTION

The WattStopper CI-305 360° passive infrared (PIR) occupancy sensors turn lighting 

systems on and off based on occupancy. 
The sensors can be configured to turn lighting on, and hold it on as long as the 

sensor detects occupancy. After no movement is detected for a user specified time 

(30 seconds to 30 minutes) the lights are switched off. A “walk-through” mode can 

turn lights off after only 3 minutes, if no activity is detected after 30 seconds of an 

occupancy detection.
The CI-305 operates on 24V supplied by WattStopper Power Packs, 24VAC or half 

wave rectified AC.

COVERAGE PATTERN

The CI-305 sensors provide a 360° coverage pattern. Two lens patterns are 

available. The CI-305 provides up to 1200 square feet of coverage and the CI-305-1 

provides up to 500 square feet of coverage. The coverage shown represents walking 

motion at a mounting height of 8 feet. For building spaces with lower levels of 

activity or with obstacles and barriers, coverage size may decrease.

Call 800.879.8585 for Technical Support

24 ft

7.3m

CI-305-1 Coverage Pattern (high density, reduced range lens)

44 ft

13.4m

CI-305 Coverage Pattern (standard lens)

Drawings not to scale.

Side View

Side View

Top View @ 8ft

Top View @ 8ft

Summary of Contents for CI-305













Reviews: