Watson Marlow Pumps 500 Series Installation, Operating And Maintenance Manual Download Page 75

Page: 75 / 157

17.2

Stop

Stops the pump. The display background changes to white. If the pump is not running
pressing this has no effect.

17.3

Increasing and decreasing flow rate

Using the

∧

∨

keys will increase or decrease the flow rate.

Decreasing flow rate

A single key press will decrease flow rate by the least significant digit of the chosen flow rate

unit.

Repeat key presses as required to achieve the desired flow rate.

Hold down the key for flow rate scrolling.

Increasing flow rate

A single key press will increase flow rate by the least significant digit of the chosen flow rate

unit.

Repeat key presses as required to achieve the desired flow rate.

Hold down the key for flow rate scrolling.

m-530pn-en-09 02-02-22

Summary of Contents for 500 Series






























































































































































Search results

Summary of Contents for 500 Series

Reviews:

Related manuals for 500 Series

Brands by name

Popular brands

Watson Marlow Pumps 500 Series, Installation, Operating And Maintenance Manual

Search results

Summary of Contents for 500 Series

Reviews:

Related manuals for 500 Series

Brands by name

Popular brands