WaterLogic WL400 Series Manual Download | Manualshive

Page: 54 / 84

background image

WL400

Manual Page 54

–

Revision: 10-23-2019

36.

Always ensure tanks are full of water before turning on the Heater or the Overload (High Limit)
will open and require manual reset. It will take the heater approximately 10 minutes to heat the
water from ambient 75°F (24°C) to the factory set point of 185°F (85°C). Dispense a cup of hot
water to ensure the temperature/odor/taste is acceptable.

WARNING!

VERY HOT WATER CAN BURN OR SCALD.

Hot water should be dispensed carefully into insulated container to avoid

«
...
52
53
54
55
56
...
»

Summary of Contents for WL400 Series





















































































Reviews:

No comments

Related manuals for WL400 Series

aroSTOR VWL B 200/5 UK

Brand: Vaillant Pages: 24

Brand: Vaillant Pages: 20

Brand: Vaillant Pages: 24

ElectriFLEX LD LE Series

Brand: Bradford White Pages: 40

Brand: Henkel Pages: 77

Brand: IONFILTER Pages: 100

Brand: Rinnai Pages: 66

Straight Line Laminator Single Head

Brand: 3M Pages: 40

Brand: Canature WaterGroup Pages: 36

Master-Fit 100 Series

Brand: A.O. Smith Pages: 40

Brand: Water Tech Pages: 20

VERSATHERM PE414-3

Brand: Chromalox Pages: 8

Brand: North Star Pages: 28

Brand: A.O. Smith Pages: 16

Brand: A.O. Smith Pages: 52

Brand: A.O. Smith Pages: 52

Brand: Frigidaire Pages: 21

Brand: Bosch Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands