Water Depot Blaster Soft, Owner'S Manual

Page: 10 / 32

10
BLASTER SOFT SET UP
NOTE: The Blaster Soft come factory set, only to be changed by trained/qualified technicians. Changes may be
necessary should the water quality change.
First Stage of Settings
Instructions Description
1. Set time clock As per normal operation
2. Press NEXT and DOWN
(or Minus Button) together
Board will go to the next setting
3. Press NEXT and DOWN
together a second time
Screen will flash this is the correct setting
4. Press NEXT ALR will flash... press plus or minus button until it says OFF
5. Press NEXT
dp will flash… press plus or minus button until it says OFF
6. Press NEXT Should read “Fill”… press plus or minus button until fill is displayed on the screen
7. Press NEXT Should read “Backwash”… press plus or minus button until backwash is displayed on screen
8. Press NEXT
Should read “Brine Down”… press plus or minus button until Brine Down is displayed on
screen
9. Press NEXT Should read “Rinse”… (this is just before ozone draw)press plus or minus button until Rinse
is displayed on screen
10. Press NEXT Should read “Brine Down”… press plus or minus button until Brine Down is displayed on
screen
11. Press NEXT Should read “End”… press Next until End is displayed on screen
12. Press NEXT Screen will go back to clock setting
Second Stage of Settings
Instructions Description
1. Press NEXT and DOWN
(or minus button) together
Should flash “Filtering or Softening”… press plus or minus button until Softening is displayed
on screen
2. Press NEXT Should flash “ Fill”…Set at 9.5 lbs (or higher if iron count is high)
3. Press NEXT
Should flash “Backwash” … Set between 8 and 12 minutes
4. Press NEXT
Should flash “Brine Draw Down”… Set for 60 minutes
5. Press NEXT Should flash “Rinse”… Set for 4 to 6 minutes
6. Press NEXT Should flash “Brine Down”… Set for 30 up to 60 minutes
7. Press NEXT
Should flash “Capacity”… (unit size) usually set for 30,000 grains
8. Press NEXT Should flash “Auto”… press plus or minus buttons until Auto is displayed on screen
9. Press NEXT Should flash “Normal”… press plus or minus buttons until Normal is displayed on screen
10. Press NEXT
Should flash “Relay” … Set for “ON” (NOTE: This can be set in time or gallons, set for time)
11. Press NEXT
Screen Should flash… Set the time you want the ozone to come on, you this by adding all
the cycles together. Add fill time, backwash time, brine draw time, and rinse time. You may
need to put the unit through a manual regeneration to see each time, write them down and
add them up. For example if you have 84 minutes in time before your ozone brine draw set it
for 2 more minutes = 86 minutes
12. Press NEXT Screen should flash… Set length of Ozone between 30 to 60 minutes
13. Press NEXT Should flash “Call”…leave OFF
14. Press NEXT
Screen will go back to clock setting
•
NOW ADJUST REGENS... EXAMPLE BAD WATER 10 Minute backwash (our example) and 60 minutes
brine… now you may want it to go off every day…or every second day…. So follow this instruction
•
Press…Next and PLUS (+)… at the same time. “hardness “NA” will flash
•
Press… NEXT….”regen” day will flash…. Press the plus (+) or minus (-) for the day to regen... if bad water
set it at 1… this means every day it will go off.
•
Press, NEXT… back to clock setting.
NOTE : Your Blaster ozone draw time setting does not work on cycles, it works on time. This bases of design is
simple, however do not set the relay too soon, it is better to be 2 to 3 minutes longer than actual cycles add up to. If
you make it too short and the valve is in rinse the ozone will come on but won’t shut off when brine draw starts.
Lastly, when the unit has finished all the cycles and goes back to service mode the ozone will automatically shut off.