WatchOvers WG13 User Manual Download Page 12

Users Manual WG13 Alarm & Keypad 04 04 2022

 

 

Carbon Monoxide (CO) Alarm 

 

 

 

Carbon Monoxide alarms should be installed in every room that have a ‘fuel burning’ appliance 
and one within 5 metres of every bedroom.   
 
Powered by a replaceable 9V battery, when triggered it makes over 85dB sounds with the 
red indicator light flashing simultaneously. The green indicator will flash once every 30 
seconds at normal working mode.  

 

The Carbon Monoxide Alarm is in the working mode after installation, with the Green LED light 
flashing once for every 30 seconds. When it detects Carbon Monoxide, the alarm will sound 
and the red LED light will flash until the carbon monoxide is cleared from the alarm.

 

 

An SMS will be sent to all numbers listed in your 

“Alarm SMS number” list. The SMS will advise 

what sensor has been triggered.

 

 

A pre-recorded phone call will be made to the number(s) saved in your “Alarm Call number” 
list advising them of the alarm being set off in line with the calls protocol, a call will be made 
to the first person on the calls list and if unanswered, the second number and so on until it has 
reached the redial limit you have set in the app under settings.  

 

 

Press the testing button to trigger the alarm signal, the alarm will sound, the LED flashes and 
releases  the  wireless  signals.  You  can  also  use  the  test  carbon  monoxide  cans to  test the 
detector.  Testing is required regularly to make sure the alarm is working correctly. 
 
For installation instructions go to our Quick Set Up Guide 

 
Notes. 

1.  This device must be paired with our base station to operate. 
2.  Do not install near the areas such as doors, windows, fans etc, where the air flows which 
would  affect  the  sensitivity;  High  humidity  areas  such  as  bathrooms,  nor  high  temperature 
places such as attic are unsuitable. The temperature should be-10°C to +50°C. 
3.  Please clean the alarm with a soft brush every six months to ensure the sensitivity and the 
life of the product. Remove the battery before cleaning. 
4.  Changes  in  environmental  conditions,  or  tampering  can  affect  the  performance  of  this 
product.  Users  are  advised  to  take  all  necessary  precautions  for  his/her  safety  and  the 
protection of the property. 
 

 

Summary of Contents for WG13
















Reviews: