Wascomat EXSM 230 S Operating & Maintenance Manual Download Page 14

Page: 14 / 124

Installation

1757

1758

1759

Mechanical installation

•

Place wide steel shims on the concrete
foundation over the bolts.

•

Lift the machine and lower it in position. Never
use the door or the door handle to lift or lower
the machine.

•

Check that the machine is level front-to-rear
and side-to-side and standing firmly on the ten
supporting points. Spacing washers must be
mounted if one or more of these points is not
resting against the floor/foundation.

•

Place flat washers over the foundation bolts
and secure the machine in position by
tightening the self-locking nuts. See illustration
below.

•

Tighten the nuts in sequence as shown.

•

Check and tighten the nuts every week for the
first month.

Fig.

2408

EXSM 230 S

EXSM 350 S

2399

Summary of Contents for EXSM 230 S





























































































































Search results

Summary of Contents for EXSM 230 S

Reviews:

Related manuals for EXSM 230 S

Brands by name

Popular brands

Wascomat EXSM 230 S, Operating & Maintenance Manual

Search results

Summary of Contents for EXSM 230 S

Reviews:

Related manuals for EXSM 230 S

Brands by name

Popular brands