Wascomat EXSM 230 S Operating & Maintenance Manual Download Page 79

Page: 79 / 124

Trouble shooting

Turn the machine’s wall switch off and on again.
Start a program.

Error code returns

No error code

Unscrew the program control unit PCB. Remove
the EPROM, then refit the same one. Check that
the EPROM is turned the right way and that all
its leg connectors enter the holder correctly.
Restart the machine.

Error code 12E returns

Machine normal

Replace the EPROM. Check that the new one
has the correct program version. Restart
machine.

Error code 12E returns

Machine normal

12E

The program control unit
cannot read the program
EPROM.

Error codes which may arise on the control panel display

2316

The marking
on the
EPROM
must be to
the left.

EPROM

Faulty program control unit
PCB. Replace PCB. The old
EPROM can probably be
reused.

Old EPROM was faulty.

Temporary loss of contact or
EPROM fitted incorrectly.

Transient fault. No action
required.

Cause/Action

Error code/symptoms

Fault-finding

Summary of Contents for EXSM 230 S





























































































































Search results

Summary of Contents for EXSM 230 S

Reviews:

Related manuals for EXSM 230 S

Brands by name

Popular brands

Wascomat EXSM 230 S, Operating & Maintenance Manual

Search results

Summary of Contents for EXSM 230 S

Reviews:

Related manuals for EXSM 230 S

Brands by name

Popular brands