Wascomat EXSM 230 S Operating & Maintenance Manual Download Page 42

Page: 42 / 124

Mechanical and electrical design

Extraction

During extraction, the motor speeds follow an extraction sequence which is
always the same. This extraction sequence is used for all standard
programs 991-999 for CLARUS machines.

The table shows the extraction speeds during the various phases of the
sequence, for various drum volumes.

The extraction sequence is as follows:

Phase 1.

Distribution period of 40 seconds, with imbalance
sensing. Imbalance sensing takes place during the
last 5 seconds.

Phase 2.

Extraction for 30 seconds.

Phase 3.

Extraction for 30 seconds.

Phase 4.

Extraction for 30 seconds.

Phase 5.

Extraction for remainder of the program’s total
extraction time.

Fig.

Summary of Contents for EXSM 230 S





























































































































Search results

Summary of Contents for EXSM 230 S

Reviews:

Related manuals for EXSM 230 S

Brands by name

Popular brands

Wascomat EXSM 230 S, Operating & Maintenance Manual

Search results

Summary of Contents for EXSM 230 S

Reviews:

Related manuals for EXSM 230 S

Brands by name

Popular brands