background image

©2012 Warn Industries, Inc.WARN® and the WARN logo are trademarks of Warn Industries Inc.

 2 

88783A3

N O T I C E

EQUIPMENT DAMAGE

•  Always refer to the installation instructions, supplied in this kit, for all wiring schematics and specific details on how to wire this WARN product to your vehicle.

• 

Always release switch when Pro-Pivot reaches the end of travel or when subject to plowing loads.  Stalling will cause overheating and reduce life of the unit.

• 

Always store this product out of the weather between use to protect against corrosion and freezing, and keep product operating smoothly.

Read installation and operating instructions thoroughly.

  

 

C A U T I O N

MOVING PARTS ENTANGLEMENT HAZARD

Failure to observe these instructions could lead to minor or moderate injury

• 

Always take time to fully read and understand the installation and operating instructions included with this product. 

• 

Always stay clear of moving parts and joints. Always keep others away when operating or adjusting  plow.

• 

Never operate this product if you are under 16 years of age.

•  Never operate this product when under the influence of drugs, alcohol or medications.

• 

Always connect red switch wire to keyed power.

• 

Never manually adjust plow with key on.

Read installation and operating instructions thoroughly.

N O T E S

• 

The Pro-Pivot is actuated by a handlebar mounted switch that directs power to the Pro-Pivot motor. The motor outputs a torque 

that is multiplied through the gear train rotating the plow blade until the limit switch terminates rotation.  The Pro-Pivot is capable 

of rotating the blade 28 degrees in each direction from center.

• 

Do not excessively load plow, bracket, and pivot.

  

 

C A U T I O N

PINCH POINTS

Failure to observe these instructions could lead to minor or moderate injury

• 

Never  operate unless Pro-Pivot is installed to plow tube base and swivel.

Read installation and operating instructions thoroughly.

  

 

C A U T I O N

BURN HAZARD

Failure to observe these instructions could lead to minor or moderate injury

• 

Always use caution when in contact with Pro-Pivot components.  Surfaces may become hot after use.

Read installation and operating instructions thoroughly.

Summary of Contents for 88700












Reviews: