W&H 20210492060001 Operator'S Manual Download Page 4 | Manualshive

Page: 4 / 23

background image

UNPACKING INSTRUCTIONS

Remove clear packaging.
Inspect the machine for any shipping damage.
Remove the side covers.
Cut the zip-tie around the motor.
Remove the motor shipping boards.
Remove the lag bolts holding the machine to the pallet.
Lift the machine off of the pallet.
Re-install the sides.
Before elevating the molder, loosen the motor lock.

Side panel Zip

‐

Tie Lag bolts

Motor shipping boards

Motor lock

«
...
2
3
4
5
6
...
»

Summary of Contents for 20210492060001
























Reviews:

No comments

Related manuals for 20210492060001

ImageQuant LAS 4000

Brand: GE Pages: 86

Brand: GE Pages: 160

Brand: GE Pages: 134

Brand: Samsung Pages: 2

Brand: B-K lighting Pages: 3

Brand: Patlite Pages: 28

Web Ankle Brace

Brand: Darco Pages: 2

Brand: Darkly Labs Pages: 13

Brand: DARAY Pages: 24

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: LaboGene Pages: 59

Brand: Datalogic Pages: 48

Brand: PageFlip Pages: 32

Brand: V-TAC Pages: 13

Brand: Velleman Pages: 16

Brand: Velleman Pages: 11

Brand: Hach Pages: 456

Brand: LSI Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands