WAGO 761-217 Manual Download Page 91

Page: 91 / 138

WAGO-TO-PASS® 761

Operation

761-217 Telecontrol Module Compact, 8 AI, Web, MODBUS485

Manual

Version 1.0.0

8.1.2.1

Inputs/Outputs

Press the

[I/O]

button to display the process values of the inputs and outputs. The

process values displayed are valid if the on-line display is green.

Figure 40: Visualization of the process values

Process values pertaining to inputs are displayed in the upper portion of the
window and those pertaining to digital and analog outputs are displayed in the
lower portion of the window.

Digital inputs configured as counter inputs are highlighted in blue.

Displaying the Analog Values

The process values of the analog inputs and outputs are displayed with 8-bit
resolution.

Summary of Contents for 761-217











































































































































Search results

Summary of Contents for 761-217

Reviews:

Related manuals for 761-217

Brands by name

Popular brands

WAGO 761-217, Manual

Search results

Summary of Contents for 761-217

Reviews:

Related manuals for 761-217

Brands by name

Popular brands