WAGO 761-217 Manual Download Page 30

Page: 30 / 138

Device Description

WAGO-TO-PASS® 761

761-217 Telecontrol Module Compact, 8 AI, Web, MODBUS485

Manual

Version 1.0.0

3.4.10

Serial Interface to the PC and MODBUS Interface

Table 11: Serial interface to the PC and MODBUS interface

Figure 10: Serial interface to the PC
and MODBUS interface

Pin

Description

Not assigned

TXD

RXD

Not assigned

GND

Not assigned

MODBUS D1 (B)

MODBUS D0 (A)

Not assigned

Table 12: PC interface cable assignment

TO-PASS

Telecontrol Module

PC (D-Sub 9)

Pin

Description

Pin

Description

TXD



RXD



TXD

GND

Connecting laptops and PCs without serial interface:

If the laptop or PC does not have a serial interface, use the USB adapter 761-
9005, which is available as an accessory.

Summary of Contents for 761-217











































































































































Search results

Summary of Contents for 761-217

Reviews:

Related manuals for 761-217

Brands by name

Popular brands

WAGO 761-217, Manual

Search results

Summary of Contents for 761-217

Reviews:

Related manuals for 761-217

Brands by name

Popular brands