manualshive.com logo in svg

Wacker Neuson DPU 5545He, Operator'S Manual

Share
Download
Wacker Neuson DPU 5545He Operator'S Manual Download Page 45

www.wackerneuson.com

EC Declaration of Conformity

Manufacturer

Wacker Neuson SE
Preußenstraße 41, 80809 München

Product

Conformity assessment procedure

 

acc. to 2000/14/EC, Appendix VIII, 2005/88/EC

 

at follow-

ing test center:

VDE Prüf- und Zertifizierungsinstitut, Merianstraße 28, 63069 Offenbach/Main

Guidelines and standards

This is to certify that this product meets and complies with the relevant regulations and re-
quirements of the following guidelines and standards:
2006/42/EC,
2000/14/EC, 2005/88/EC

Authorized person for technical documents:

 Axel Häret

Munich, 08.03.2010

Type

DPU 5545

Product type

Vibrating plate

Item  no.

0610351, 0610352,  
0610353

Installed power output

kW

6,4

Measured sound pow-
er level

dB(A) 107

Guaranteed sound 
power level

dB(A) 108

Dr. Michael Fischer
Head of Research and Development

Franz Beierlein
Head of product management

Summary of Contents for DPU 5545He

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands