Vzense DCAM560C User Manual Download

Page: 44 / 46

10 Customization Service

Vzense team has rich experience in ToF product design and delivery, we welcome

customer to send customization requirement besides the standard module.

Reasonable NRE fee shall be charged depends on the requirement.

Appendix

ROHS Declaration

Laser Specification

CAUTION

Use of controls or adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure.

Complies with 21 CFR 1040.10 and 1040.11 except for conformance with
IEC 60825-1 Ed.3., as described in Laser Notice No. 56, data May 8, 2019.

The following Class1 laser label is located on the bottom of the sensor.

Manufacturer

Name: Qingdao Vzense Technology Co., Ltd.

Address: 3 Building, Qingdao Research Institute of Beihang University, No. 393

Songling Road, Laoshan District, Qingdao, Shandong

Summary of Contents for DCAM560C















































Search results

Summary of Contents for DCAM560C

Reviews:

Related manuals for DCAM560C

Brands by name

Popular brands

Vzense DCAM560C, User Manual

Search results

Summary of Contents for DCAM560C

Reviews:

Related manuals for DCAM560C

Brands by name

Popular brands