manualshive.com logo in svg

Volvo VHD, Operator'S Manual

The Volvo VHD is a rugged and dependable truck that delivers superior performance on any job site. Stay updated on maintenance and repairs with the free service bulletins and user manuals available for download on our website. Ensure optimal performance and safety by accessing these valuable resources only at manualshive.com.

Share
Download
background image

90

Instruments and Controls

A bulb change tool is included with the
ignition keys on the keychain, or can be or-
dered from your Volvo Truck dealer under
part number 1089953. Use only this tool to
change bulbs in the instrument cluster.

To remove bulb, insert tool onto the bulb
assembly, rotate a 1/4 turn counterclock-
wise and pull the bulb assembly out of the
cluster.

Insert a new bulb into the tool and install it
into the cluster. Rotate the bulb a 1/4 turn
clockwise and pull the tool off of the bulb
assembly.

NOTE! The telltale area in the right part of
the instrument does not use all spaces for
active telltales. These bulbs can be used for
spare bulbs.

Lift up the instrument cluster and fasten the
two screws at the top of the cluster.

W3000642

Summary of Contents for VHD













































































































































































































































































































Reviews:

No comments

Related manuals for VHD

Versalift TEL-29-N Operator'S Manual preview
TEL-29-N
Brand: Versalift Pages: 46
U-Line H-8921 Manual preview
H-8921
Brand: U-Line Pages: 9
RAM 2014 TRUCK 1500 Owner'S Manual Supplement preview
2014 TRUCK 1500
Brand: RAM Pages: 40
Komatsu HD605-7R Brochure preview
HD605-7R
Brand: Komatsu Pages: 6
Vestil PM2-3344-SLP Instruction Manual preview
PM2-3344-SLP
Brand: Vestil Pages: 6
Vestil CARPET-45 Instruction Manual preview
CARPET-45
Brand: Vestil Pages: 5
Terex TA35 Operation, Safety, Maintenance Manual preview
TA35
Brand: Terex Pages: 150
Still ECH 15 Original Instructions Manual preview
ECH 15
Brand: Still Pages: 104
Still EXU-S 22 Original Instructions Manual preview
EXU-S 22
Brand: Still Pages: 122
Still EXH-S 20 Original Instructions Manual preview
EXH-S 20
Brand: Still Pages: 132
Big Joe PDBB-20-T12 Operation, Maintenance, Repair Parts List preview
PDBB-20-T12
Brand: Big Joe Pages: 114

Brands by name

Popular brands

Load more brands