manualshive.com logo in svg

Volvo VHD, Operator'S Manual

The Volvo VHD is a rugged and dependable truck that delivers superior performance on any job site. Stay updated on maintenance and repairs with the free service bulletins and user manuals available for download on our website. Ensure optimal performance and safety by accessing these valuable resources only at manualshive.com.

Share
Download
background image

Engine Start and Operation

203

Coolant

Temperature

Preheater

Engagement

Time (seconds)

Above +120

F (50

C)

0

Above +50

F (10

C)

0

B4

F (-15

C)

and +50

F (10

C)

25 ± 2 to 50 ± 2

Below +4

F (-15

C)

50

When the engine has started, the preheater
may be re-engaged to assist in faster engine
warm-up. To re-engage, turn the key to the
preheat position and the preheater will en-
gage. The starter will not engage as the
start position is locked out.

Engines Without Preheater

Engines not equipped may, depending on
coolant temperature, take longer to start. If
this should happen, do not release the igni-
tion key until the engine has started (while
still observing the 30 second maximum
cranking time).

Summary of Contents for VHD













































































































































































































































































































Reviews:

No comments

Related manuals for VHD

Magliner GEMINI XL Owner'S Manual preview
GEMINI XL
Brand: Magliner Pages: 10
Magliner CooLift CTA43 Service Manual preview
CooLift CTA43
Brand: Magliner Pages: 64
UniCarriers PLL Series Instruction Handbook Manual preview
PLL Series
Brand: UniCarriers Pages: 84
Mammuth PT15E Instructions For Assembly And Use preview
PT15E
Brand: Mammuth Pages: 51
Paccar Kenworth C500 2012 Manual preview
Kenworth C500 2012
Brand: Paccar Pages: 276
Peterbilt 220 Operator'S Manual preview
220
Brand: Peterbilt Pages: 136
International Trucks ProStar+ Eagle Series. Operator'S Manual preview
ProStar+ Eagle Series.
Brand: International Trucks Pages: 263
SIBS Fuso Canter Workshop Manual preview
Fuso Canter
Brand: SIBS Pages: 41

Brands by name

Popular brands

Load more brands