manualshive.com logo in svg

Volvo VHD, Operator'S Manual

The Volvo VHD is a rugged and dependable truck that delivers superior performance on any job site. Stay updated on maintenance and repairs with the free service bulletins and user manuals available for download on our website. Ensure optimal performance and safety by accessing these valuable resources only at manualshive.com.

Share
Download
background image

58

Additional Safety Features

Warning Labels

The label attached to the left hand sunvisor
shows the year and month when a Volvo
Truck dealer should be contacted for a
specific inspection and for a possible re-
placement of the airbag. This is done to
guarantee the function of the airbag after
the stated date. Replace the label when re-
placing the airbag module. Never attempt
to make any adjustments to SRS compo-
nents yourself.

T8006843

Steering shafts and steering wheel should
not be removed, adjusted or replaced with-
out following the proper work procedure.
Failure to do so can damage the SRS sys-
tem to the point where it does not work any
longer. A warning label is located on the
upper steering shaft.

T8006842

There is also a label on the inside of the
windshield that indicates the inclusion of
an airbag to the vehicle safety features.

T8006841

When equipped with an airbag, a label
about the correct procedure for protecting
small children and protecting the driver is
attached to the left hand, overhead storage
lid or back of sunvisor.

W8002741

Summary of Contents for VHD













































































































































































































































































































Reviews:

No comments

Related manuals for VHD

Komatsu Galeo HD405-7R Brochure preview
Galeo HD405-7R
Brand: Komatsu Pages: 6
Komatsu 960E-1 - Shop Manual preview
960E-1 -
Brand: Komatsu Pages: 51
MAKINEX PHT2-140 Operator'S Manual preview
PHT2-140
Brand: MAKINEX Pages: 37
SAF-HOLLAND FWAL Series Rebuild/Repair Manual preview
FWAL Series
Brand: SAF-HOLLAND Pages: 24
Reese 30923 Product Instructions preview
30923
Brand: Reese Pages: 7

Brands by name

Popular brands

Load more brands