manualshive.com logo in svg

Volvo VHD, Operator'S Manual

The Volvo VHD is a rugged and dependable truck that delivers superior performance on any job site. Stay updated on maintenance and repairs with the free service bulletins and user manuals available for download on our website. Ensure optimal performance and safety by accessing these valuable resources only at manualshive.com.

Share
Download
background image

Engine Start and Operation

215

Idle Shutdown Timer

The idle shutdown timer can be pro-
grammed to shut the engine down after a
specific engine idling time. The program
can not be changed by the operator but
requires a special tool (Pro-Link) that con-
nects to the engine electronic control unit.
This is available at your Volvo Truck dealer.

The time can be set to these time intervals:

Volvo

1 to 40 minutes

Cummins

1 to 100 minutes

Detroit

2 to 100 minutes

The engine will shut down at the set time
under the following conditions:

•

Vehicle speed is 0.

•

Engine is running at idle speed.

•

Coolant temperature is above
113

F (45

C).

•

Parking brake is applied.

These are the standard choices when the
vehicle is delivered. For other customer
adaptation choices, contact your Volvo
Truck dealer for more information.

Summary of Contents for VHD













































































































































































































































































































Reviews:

No comments

Related manuals for VHD

Suzuki Carry Pro Manual preview
Carry Pro
Brand: Suzuki Pages: 240
Rail-Ability JCB 714 Manual preview
JCB 714
Brand: Rail-Ability Pages: 43
Tractel Group 251179 Operating And Maintenance Instructions Manual preview
251179
Brand: Tractel Group Pages: 20
Tractel Pioneer LID Operating And Maintenance Instructions Manual preview
Pioneer LID
Brand: Tractel Pages: 17
Franklin 70027 Owner'S Manual & Safety Instructions preview
70027
Brand: Franklin Pages: 8
Raven RoGator 64 Series Installation Manual preview
RoGator 64 Series
Brand: Raven Pages: 80
Gude GHW 2500 PA Original Instructions Manual preview
GHW 2500 PA
Brand: Gude Pages: 52

Brands by name

Popular brands

Load more brands