manualshive.com logo in svg

Volvo VHD, Operator'S Manual

The Volvo VHD is a rugged and dependable truck that delivers superior performance on any job site. Stay updated on maintenance and repairs with the free service bulletins and user manuals available for download on our website. Ensure optimal performance and safety by accessing these valuable resources only at manualshive.com.

Share
Download
background image

Fifth Wheel Instructions

267

Fifth Wheel Slider (option)

The fifth wheel comes standard with an air
operational slider. To remain within legal
weight limits, this feature allows the driver
to distribute the load easily on the axles.

The air operated slider takes the work out
of adjusting the tractor for various trailer
loads. The fifth wheel portion is easily ad-
justed, even with a fully loaded trailer
connected.

Movement between the adjustable saddle
plate and the stationary base plate rail can
result in wear, causing longitudinal, latitu-
dinal and vertical slack. Field repairs can
be made to reduce this slack for additional
service life.

W9000205

Summary of Contents for VHD













































































































































































































































































































Reviews:

No comments

Related manuals for VHD

Titan LCF55 Owner'S Manual preview
LCF55
Brand: Titan Pages: 13
RAM Chassis Cab 2014 Owner'S Manual preview
Chassis Cab 2014
Brand: RAM Pages: 543
Jet 140016 Owner'S Manual preview
140016
Brand: Jet Pages: 16
U-Line H-1364 Assembly preview
H-1364
Brand: U-Line Pages: 4
Fronius 8,045,368 Operating Instructions Manual preview
8,045,368
Brand: Fronius Pages: 60
Baxtran ARN Manual preview
ARN
Brand: Baxtran Pages: 29

Brands by name

Popular brands

Load more brands