manualshive.com logo in svg

Volvo VHD, Operator'S Manual

The Volvo VHD is a rugged and dependable truck that delivers superior performance on any job site. Stay updated on maintenance and repairs with the free service bulletins and user manuals available for download on our website. Ensure optimal performance and safety by accessing these valuable resources only at manualshive.com.

Share
Download
background image

88

Instruments and Controls

Auto Neutral Telltale

The Auto Neutral Telltale is for the Allison
WTEC III transmission. The green indica-
tor lights up when the transmission is in
auto neutral. Auto neutral is activated just
before the vehicle comes to a complete stop
(less than 1.5 mph [2.5 km/h]). The gear is
re-engaged shortly (1–2 seconds) after the
brake pedal is released.

Allow for the gear re-engagement when ap-
plying throttle; do not increase engine
speed before the transmission has engaged.
If the engine speed is too high, the trans-
mission will not engage.

CAUTION

When operating the vehicle on normal
grades (less than 4%), a slight roll-back
can be experienced when the brake
pedal is released and before the trans-
mission re-engages.

NOTE! When operating on severe grades
(more than 5%), the transmission has a
safety feature that can be used. Before re-
leasing the brake pedal, manually press the
“DRIVE” key on the Allison gear selector,
and the gear is re-engaged manually to as-
sist in preventing roll-back.

W3004308

Summary of Contents for VHD













































































































































































































































































































Reviews:

No comments

Related manuals for VHD

Paccar Kenworth T170 Hybrid 2011 Builder'S Manual preview
Kenworth T170 Hybrid 2011
Brand: Paccar Pages: 179
Cognito 110-90910 Install Sheet preview
110-90910
Brand: Cognito Pages: 10
Magliner CooLift CTA43 Service Manual preview
CooLift CTA43
Brand: Magliner Pages: 64
Total Source TSP5500 Operating Instructions & Parts List Manual preview
TSP5500
Brand: Total Source Pages: 11
Flextool TUFFTRUK B450E Manual preview
TUFFTRUK B450E
Brand: Flextool Pages: 10
DAF 95XF Manual preview
95XF
Brand: DAF Pages: 312

Brands by name

Popular brands

Load more brands