manualshive.com logo in svg

Volvo VHD, Operator'S Manual

The Volvo VHD is a rugged and dependable truck that delivers superior performance on any job site. Stay updated on maintenance and repairs with the free service bulletins and user manuals available for download on our website. Ensure optimal performance and safety by accessing these valuable resources only at manualshive.com.

Share
Download
background image

240

Brakes

Volvo Exhaust Brake

The exhaust brake is standard on the Volvo
D12 engine. It is used to reduce wear on
the brake linings. The exhaust brake is
most effective at high engine speeds (1500
to 2300 r/min). The exhaust brake is auto-
matically disengaged if the engine speed
drops to or below 1100 r/min.

The exhaust brake works by containing the
exhaust gases in the exhaust manifold,
thereby making the engine work against the
back pressure. This provides a retarding
force on the drive wheels.

The exhaust brake is operated by a two-
position switch in the right-hand switch
cluster. For the exhaust brake to function,
the following must be in effect:

•

The switch is ON

•

Accelerator and clutch pedals are fully
released

•

Engine speed exceeds 1100 r/min

When the cruise control is engaged, the ex-
haust brake automatically engages if the
selected cruise speed is exceeded by ap-
proximately 5 mph (8 km/h). The exhaust
brake is then disengaged when the speed
has returned to approximately 3 mph (5
km/h) above selected cruise speed.

NOTE! For both exhaust and engine
brakes, use a “one gear” driving strategy
when going downhill to keep engine speed
up for effective braking (for example: up-
hill in 7th gear and downhill in 6th).

W3001324

Summary of Contents for VHD













































































































































































































































































































Reviews:

No comments

Related manuals for VHD

Still HPT-20 Original Instructions Manual preview
HPT-20
Brand: Still Pages: 78
Still SXH-20 Original Instructions Manual preview
SXH-20
Brand: Still Pages: 126
Still EXH-SF 20 Original Instructions Manual preview
EXH-SF 20
Brand: Still Pages: 138
Powertow 65 EZ VIPER Owner'S Manual preview
65 EZ VIPER
Brand: Powertow Pages: 12
Trane Thermo King ES300 Installation Manual preview
Thermo King ES300
Brand: Trane Pages: 66
Haklift HAVA1500MA Original Instructions Manual preview
HAVA1500MA
Brand: Haklift Pages: 26
Rail-Ability SUPER BOSS Rail Operations & Emergency Recovery Procedures preview
SUPER BOSS
Brand: Rail-Ability Pages: 14
U-Line H-4937 Manual preview
H-4937
Brand: U-Line Pages: 6

Brands by name

Popular brands

Load more brands