Volvo Penta D4-260 Operator'S Manual Download Page 75

Page: 75 / 124

WARNING!

Hot oil and hot surfaces can cause burns.

1 Run the engine until warm so that the oil is easier

to pump. Then stop the engine and wait 10 minutes.

2 Connect the oil suction pump to the draining pipe.

Pump out the oil.

3 Replace the oil filter and by-pass filter at every oil

change, see section

Oil Filter/By-pass Filter,

Change page 73

4 Fill with oil to the correct level through the filling hole

on the top of the engine. Oil quantity, see section

Technical Data page 115

5 Start the engine. Run the engine until it reaches

normal operating temperature. The oil level shall be
checked with the engine warm.
Check that the low oil pressure lamp goes out and
that there are no leaks around the oil filter.

6 Turn off the engine. Wait ten minutes before check-

ing the oil level. Top up as needed.

Hand in the old oil and oil filter to a re-cycling station.

Oil Filter/By-pass Filter, Change

The oil filter and by-pass filter must be replaced at
every oil change.
Deposit the old filter at a waste management facility.

WARNING!

Hot oil and hot surfaces can cause burns.

1 Put a suitable container under the filter to collect

any spilled oil.

2 Clean the filter bracket.

3 Unscrew the by-pass filter (

) and the oil filter (

)

with a suitable filter puller.

4 Check that the mating surfaces on the filter bracket

are clean and that no remnants of the old gaskets
are left.

5 Moisten the gaskets on the new filters with engine

oil.

6 Screw on the filter by hand until the rubber gasket

touches the filter bracket mating surface. Then
tighten an additional 3/4 turn.

7 Start the engine, run at low idle, and check that no

leakage occurs. Check the oil level after the engine
has stopped.

Maintenance

7748921 04-2008

Summary of Contents for D4-260





























































































































Search results

Summary of Contents for D4-260

Reviews:

Related manuals for D4-260

Brands by name

Popular brands

Volvo Penta D4-260, Operator'S Manual

Search results

Summary of Contents for D4-260

Reviews:

Related manuals for D4-260

Brands by name

Popular brands