Volvo Penta D4-260 Operator'S Manual Download Page 104

Page: 104 / 124

Calibration and Settings

Settnings menu

Settings are entered and certain calibrations are car-
ried out in the Settings menu.

Navigate through the menus by turning and depressing
the control panel wheel.

It is always possible to return to the menu above by
pressing

. Repeated presses or holding the button

down for >3 seconds will return to the main menu.

NOTICE!

Only installed functions are shown in the set-

tings menu.

1 Turn clockwise until

Settings

is shown on the dis-

play.

2 Press the wheel to access the settings menu.

3 Navigate by turning the wheel.

Depth Alarm

Setting the depth alarm for the Volvo Penta echo soun-
der.

The setting need only be entered at one display, at one
station.

1 Activate the station.

2 Turn until

Depth Alarm

is shown in the settings

menu. Press the wheel to reach the submenu.

Depth Alarm

, press the wheel to switch the func-

tion on or off.

p0005184

P0001015

P0001028

P0001027

102

7748921 04-2008

Summary of Contents for D4-260





























































































































Search results

Summary of Contents for D4-260

Reviews:

Related manuals for D4-260

Brands by name

Popular brands

Volvo Penta D4-260, Operator'S Manual

Search results

Summary of Contents for D4-260

Reviews:

Related manuals for D4-260

Brands by name

Popular brands