Volvo Penta D4-260 Operator'S Manual Download Page 112 | Manualshive

Page: 112 / 124

background image

Joystick

Joystick calibration need only be carried out if boat
movements do not correspond to joystick movements.

When calibrating the joystick the boat must be driven
on open waters in safe conditions. Avoid calibrating in
high winds or currents that can influence the result of
the calibration.

Allow the boat to run for a fairly long distance during
the calibration. Hold the joystick firmly in position.

Calibration can only be carried out at a helm station
that is equipped with both a joystick and a control
panel.
Calibration need only be done in one direction, port or
starboard.

1 Move the control lever(s) to neutral.

2 Activate docking mode by depressing the docking

button.

3 An audible signal will confirm that docking mode is

activated and the docking button lamp will light up.

P0006292

Calibration and Settings

110

7748921 04-2008

«
...
110
111
112
113
114
...
»

Summary of Contents for D4-260





























































































































Reviews:

No comments

Related manuals for D4-260

Brand: Daedong Pages: 51

Brand: Flux Pages: 20

MerCruiser Diesel Inboard 2.8L

Brand: Mercury Pages: 93

Brand: GAPOSA Pages: 2

Brand: Evolution Technologies Pages: 12

Confidant ZT710

Brand: Kohler Pages: 24

2005 ENDUCROSS EC 125

Brand: GAS GAS Pages: 50

Brand: Volvo Penta Pages: 44

Brand: Volvo Penta Pages: 90

Brand: RADEMACHER Pages: 88

Brand: MAG Pages: 13

Brand: FIAMA Pages: 7

Brand: CAME Pages: 64

Brand: Yanmar Pages: 280

Brand: Yanmar Pages: 76

Brand: Yanmar Pages: 234

Brand: Honda Pages: 60

Brand: Honda Pages: 149

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands