Volvo Penta D4-260 Operator'S Manual Download Page 50

Page: 50 / 124

Engine Oil Level

Explanation:

Oil level too low.

P0005017

WARNING!

Engine Oil Level See Oper-

ator's Manual

NOTICE!

In rough following seas or head seas, the system can

incorrectly sense that the engine oil level is too low. If this happens,
acknowledge the fault, and check the points below for safety rea-
sons.

Symptom:

None.

Action:

• Check the oil level in the engine. Please refer to

Oil level,

checking and topping up page 72

• Check that no leakage occurs.

• Please contact a Volvo Penta workshop if the fault remains.

Engine Oil Pressure

Explanation:

Oil pressure too low.

P0005018

WARNING!

Engine Oil Pressure See

Operator's Manual
Stop Engine

Symptom:

Engine power is reduced.

Action:

• Check the oil level in the engine. Please refer to

Oil level,

checking and topping up page 72

• Check that the oil filters are not blocked. Replace filters if nec-

essary.

• Check that no leakage occurs.

• Please contact a Volvo Penta workshop if the fault remains.

Check drive oil

Explanation:

Oil level too low.

P0001194

CAUTION!

Check drive oilSee Opera-

tor's Manual

Symptom:

Engine power is reduced.

Action:

• Check the oil level. Please refer to

Maintenance page 90

• Fill up with oil to the right level.

• Check that no leakage occurs.

• Please contact a Volvo Penta workshop if the fault remains.

Fault Code Register

7748921 04-2008

Summary of Contents for D4-260





























































































































Search results

Summary of Contents for D4-260

Reviews:

Related manuals for D4-260

Brands by name

Popular brands

Volvo Penta D4-260, Operator'S Manual

Search results

Summary of Contents for D4-260

Reviews:

Related manuals for D4-260

Brands by name

Popular brands