Volvo Penta D4-260 Operator'S Manual Download Page 51

Page: 51 / 124

Transmission Oil Pressure

Explanation:

Reverse gear oil pressure too low.

P0005023

WARNING!

Transmission Oil Pressure

See Operator's Manual

Symptom:

None.

Action:

• Check the oil level. Please refer to

Oil level, checking and top-

ping up

• Check that the oil strainer is not blocked.

• Check that no leakage occurs.

• Please contact a Volvo Penta workshop if the fault remains.

Battery Voltage

Explanation:

Battery voltage too low.

P0005024

WARNING!

Battery Voltage See Oper-

ator's Manual

Symptom:

None.

P0002364

Action:

• Check the batteries fluid level

• Check belt tension.

• Please contact a Volvo Penta workshop if the fault remains.

Auxiliary Stop

Explanation:

External stop signal.

P0005025

WARNING!

Auxiliary Stop See Opera-

tor's Manual

Symptom:

Engine stops or can not be started.

Action:

• Check emergency stop button if any. Reset if necessary.

Please refer to

Engine Shutdown page 38

• Please contact a Volvo Penta workshop if the fault remains.

Fault Code Register

7748921 04-2008

Summary of Contents for D4-260





























































































































Search results

Summary of Contents for D4-260

Reviews:

Related manuals for D4-260

Brands by name

Popular brands

Volvo Penta D4-260, Operator'S Manual

Search results

Summary of Contents for D4-260

Reviews:

Related manuals for D4-260

Brands by name

Popular brands