Volvo Penta D34A MS Operator'S Manual Download Page 74

Page: 74 / 89

Technical Data

D34A MT

General

Number of cylinders ..............................................

Displacement .........................................................

33,93 liters (2071 in

)

Nominal idling speed .............................................

not available

Low idling speed ....................................................

625 ±25 rpm

High idling speed ...................................................

2006 rpm [rating 1]

2150 rpm [rating 2]

Valve clearance* ...................................................

0,4 mm (0,016”) [inlet]

0,5 mm (0,020”) [outlet]

Compression pressure
at starter motor speed (120 rpm) ..........................

2,45 MPa (356 psi)

Dry Weight*, engine with heat exchanger,
without reverse gear or clutch, approx. ................

3300 kg (7277 lbs)

*excl. engine oil & coolant

Exhaust temperatures:

701 kW Rating 1

1222 r/min. .............................................................

327°C (621°F)

1540 r/min. .............................................................

406°C (763°F)

1763 r/min. .............................................................

416°C (781°F)

1940 r/min. .............................................................

427°C (801°F)

Exhaust temperatures:

776 kW Rating 2

1260 r/min. .............................................................

340°C (644°F)

1587 r/min. .............................................................

415°C (779°F)

1817 r/min. .............................................................

430°C (806°F)

2000 r/min. .............................................................

440°C (824°F)

* Applies to cold or warm engine (stopped).

Lubricating system

Oil capacity, approx.

including oil filters

No engine inclination .............................................

140 liters (37,0 US gals)

volume difference min. –max. ..............................

28 liters (7,4 US gals)

Oil pressure, hot engine:

at operating speed .................................................

0,50-0,64 MPa (71-93 psi)

at idling speed .......................................................

min.0,20-0,30 MPa (29-43 psi)

Cooling system

Freshwater system capacity
including heat exchanger, approx. ........................

142 liters (37,5 US gals)

Electrical system

System voltage .....................................................

24V

AC generator:

voltage/max. amperage .........................................

24V/35A

output, approx. ......................................................

840W

Battery electrolyte density at +25°C (77°F):

fully charged battery ..............................................

1,28 g/cm

= 0,0462 lb/in

(1,24 g/cm

= 0,0448 lb/in

battery recharged at ..............................................

1,24 g/cm

= 0,0448 lb/in

(1,20 g/cm

= 0,0434 lb/in

* Note. Applies to batteries with tropical acid.

Plus d'informations sur : www.dbmoteurs.fr

Summary of Contents for D34A MS


























































































Search results

Summary of Contents for D34A MS

Reviews:

Related manuals for D34A MS

Brands by name

Popular brands

Volvo Penta D34A MS, Operator'S Manual

Search results

Summary of Contents for D34A MS

Reviews:

Related manuals for D34A MS

Brands by name

Popular brands