Volvo Penta D34A MS Operator'S Manual Download Page 43 | Manualshive

Page: 43 / 89

background image

43

Maintenance: Engine

Turning the engine

Insert the turning bar in the holes on the flywheel.
Turn the engine manually.

Warning! Make sure the turning bar is

removed before cranking the engine.

Vibration damper inspection

NOTE! When installing a damper protective
cover on the engine, do not use a cover
enclosing the damper.

Visually check for fluid leaks, flaws, distortion, or dis-
coloration or flaking of painted surfaces. Also check
for swelling (by measuring with a scale), and fluid le-
aks past staked portions.

Re-tighten bolts and nuts

Re-tighten the bolts and nuts on the following compo-
nents:

* Timing gear case

* Crankshaft pulley

* Mounting brackets

* Exhaust manifold

* Turbocharger

* Cylinder heads

Check the cylinder head bolts and re-tighten them in
number sequence (1-2-3-4-5-6-7-8) if necessary. The
tightening torques of the bolts and nuts can be found
in technical data section of this manual.

NOTE! In case retightening is necessary, first
unscrew the bolts completely.

Plus d'informations sur : www.dbmoteurs.fr

«
...
41
42
43
44
45
...
»

Summary of Contents for D34A MS


























































































Reviews:

No comments

Related manuals for D34A MS

Brand: Daihatsu Pages: 196

Brand: Zenoah Pages: 20

Brand: Navistar Pages: 24

Brand: Beninca Pages: 72

Calzoni MR Series

Brand: Parker Pages: 50

Brand: Hatz Pages: 112

Brand: Yamaha Pages: 51

Brand: Simple Motors Pages: 6

Brand: CAME Pages: 96

B&W S50MC-C8-TII

Brand: Man Pages: 403

Brand: Black Bruin Pages: 44

Brand: Wood-mizer Pages: 24

PowerMax Series

Brand: Seamax Pages: 12

Brand: LIMBACH Pages: 39

Brand: Nakanishi Pages: 4

Brand: Nakayama Pages: 11

Brand: Danfoss Pages: 2

Brand: Kärcher Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands