Vogt TUBE-ICE 03TA Service Manual Download Page 30

Page: 30 / 122

03TA Service Manual

INSTALLING YOUR TUBE-ICE

MACHINE

4/2/14

3-8

Wiring and Electrical Connection

! WARNING !

Only service personnel experienced in refrigeration and qualified to work with high voltage

electrical equipment should be allowed to install or work on the Tube-Ice

machine.

! WARNING !

Refer to TABLE 3-2 below to properly size wiring connections. A fused disconnect must be
provided near the Tube-Ice

machine. Connect 3 phase power, L1, L2, L3 to the power distribution

block (PDB) for operation of the Tube-Ice

machine and its controls. Rotation checking of cutter

motor and water pump is required (see following section). Also, if one leg of the 3 phase power is
higher or lower (“Wild”), then it should be connected to terminal #L2. Connect the “Ground” wire
to the “Ground” lug provided.

FIGURE 3-6

Control Panel Power Connections

Standard Voltages

Water Cooled

Air Cooled

F.L.A.

Min.

Ampacity

Max. Fuse

F.L.A.

Min.

Ampacity

Max. Fuse

208/230, 3ph, 60 Hz

48.3

58.6

100

54.3

64.6

110

460, 3ph, 60 Hz

23.7

28.7

26.4

31.4

200, 3ph, 50 Hz

50.9

61.8

110

57.5

68.4

115

400, 3ph, 50 Hz

24.2

30.4

27.2

32.2

TABLE 3-2

Electrical Specifications

AUX CONNECTIONS
Cutter Motor, Pump Motor &
Compressor Interlocks

MAIN MACHINE POWER
Incoming power to be connected to
Power Distribution Block (PDB)

AIR COOLED CONDENSER
CONNTECTIONS
Power for Fan Motors (B7, B8 & B9)

AIR COOLED CONDENSER CONNTECTIONS
Power for Condenser control circuit (11 & 22)

Summary of Contents for TUBE-ICE 03TA



























































































































Search results

Summary of Contents for TUBE-ICE 03TA

Reviews:

Vogt TUBE-ICE 03TA, Service Manual, Page: 30 / 122

Search results

Summary of Contents for TUBE-ICE 03TA

Reviews: