Vogt TUBE-ICE 03TA Service Manual Download Page 119

Page: 119 / 122

03TA Service Manual

INDEX

4/21/14

12-1

12. Index

A Valve (Liquid Feed Solenoid Valve) ------------- 4-1, 5-1, 9-6

Accumulator ----------------------------------------------------- 4-1, 5-1

Adding Refrigerant --------------------------------------------------- 5-4

Air - cooled Condenser Wiring (3 phase) ------------------- 3-16

Air-Cooled Condenser -------------------------------------------- 9-13

Air-Cooled Condenser Data ------------------------------------- 3-12

Air-Cooled Condenser Installation ----------------------------- 3-10

Air-Cooled Piping Schematic -------------------------------------- 4-4

Air-Cooled Units ------------------------------------------------------ 9-5

Allen-Bradley Switch ------------------------------------------------- 9-3

Assembly Drawing, Air-Cooled ----------------------- 1-4, 1-5, 1-6

Assembly Drawing, Water Cooled ------------------ 1-7, 1-8, 1-9

Automatic blowdown ------------------------------------------------- 9-1

Basic Product Warranty ------------------------- inside back cover

Bearing, Cutter ----------------------------------------------- 9-19, 9-20

Bill of Lading ----------------------------------------------------------- 2-1

Bin, Electronic Thermostat Programming ------------------- 3-19

Bin, Electronic Thermostat Installation ----------------------- 3-18

Blowdown -------------------------------------------------------------- 9-1

Burnout, Compressor---------------------------------------------- 9-15

Capacity Ratings --------------------------------------------------- 11-2

Centrifugal Pump --------------------------------------------------- 9-11

Charging Refrigeration Systems --------------------------------- 1-2

Check Valve ----------------------------------------------------------- 4-2

Checklist, Daily -------------------------------------------------------- 7-9

Checklist, Start-up---------------------------------------------------- 5-2

Chemical Cleaning --------------------------------------------------- 7-5

Circuit Breaker, Control --------------------------------------------- 6-5

Circulating Water Pump Motor ---------------------------------- 9-11

Clean/Ice Switch ------------------------------------------------------ 6-4

Cleaning Procedure -------------------------------------------------- 7-1

Compressor ------------------------------------------------------------ 7-6

Compressor Crankcase Heater----------------------------------- 9-7

Compressor Lubrication -------------------------------------------- 7-6

Compressor Motor Burnout -------------------------------------- 9-15

Compressor Unloader --------------------------------------------- 9-16

Compressor, Contactor --------------------------------------------- 6-5

Condenser Cleaning ----------------------------------------- 7-5, 9-13

Condenser Fan Contactor (FC) ----------------------------- 6-5, 6-6

Condenser Fan Switch ---------------------------------------------- 9-5

Condenser Piping (Cold Weather Valve Kit) ---------------- 3-14

Condenser Water Usage ---------------------------------------- 11-3

Condenser, Air-cooled Cleaning ------------------------------- 9-13

Condenser, Air-cooled Heat Rejection ----------------------- 3-12

Condenser, Pressure Switch (CPS) ----------------------------- 9-5

Condenser, Water Cooled Maintenance ----------------------- 7-5

Control Circuit Protection ----------------------------------------- 9-10

Control Panel ---------------------------------------------------------- 6-1

Control Panel Parts -------------------------------------------------- 6-5

Control, Relay (CR) -------------------------------------------------- 6-5

Cooling Tower --------------------------------------------------------- 3-7

Crankcase Heater ---------------------------------------------- 7-6, 9-7

Crushed Ice Production ------------------------------------------- 9-21

Cutter & Bearing Removal/Installation ------------------------ 9-18

Cutter, Assembly --------------------------------------------------- 9-19

Cutter, Bearing ----------------------------------------------- 9-18, 9-19

Cutter, Bearing Support------------------------------------ 9-18, 9-19

Cutter, Disc Assembly ------------------------------------- 9-18, 9-19

Cutter, Drive Parts ------------------------------------------ 9-18, 9-19

Cutter, Gear Reducer ------------------------ 7-7, 9-10, 9-18, 9-19

Cutter, Motor -------------------------------------------------- 9-18, 9-19

Cutter Assembly ---------------------------------------------------- 9-20

Cutter Parts (crushed Ice) ---------------------------------------- 9-20

Cutter/Water Tank Parts (cylinder ice) ----------------------- 9-18

D Valve (Thawing Gas) -------------------------------------- 4-1, 9-6

Daily Check List ------------------------------------------------------- 7-9

Drive gear------------------------------------------------------------- 9-19

Electrical Connection ------------------------------------------------ 3-8

Electrical Schematic All Voltages 50-60 Hz. ------------------ 6-7

Electrical, Controls --------------------------------------------------- 6-5

Enclosure --------------------------------------------------------------- 6-1

Energy Saving --------------------------------------------------------- 1-1

Equivalent Feet Due To Friction -------------------------------- 3-15

Fan Contactor (FC) -------------------------------------------------- 6-5

Filter/Drier -------------------------------------------------------------- 4-1

Float Valve (Make-Up Water) ------------------------------------- 9-1

Freeze Period --------------------------------------------------------- 4-2

Freeze-Up Due To Extended Freezing Period --------------- 8-4

Freeze-Up Due To Ice Failing To Discharge ------------------ 8-5

Freezer ------------------------------------------------------------------ 4-1

Freezer Pressure Switch ------------------------------------------- 9-3

Gear Reducer ------------------------------------------------------- 9-11

Harvest Period -------------------------------------------------------- 4-2

Head Pressure -------------------------------------------------------- 9-4

Heat Exchanger ------------------------------------------------------- 4-1

Heater, Crankcase --------------------------------------------------- 9-7

High Head Pressure (Air-Cooled) ------------------------------ 8-10

High Head Pressure (Water Cooled) ---------------------------- 8-9

High/Low Pressure Switch ----------------------------------------- 9-4

Summary of Contents for TUBE-ICE 03TA



























































































































Search results

Summary of Contents for TUBE-ICE 03TA

Reviews:

Vogt TUBE-ICE 03TA, Service Manual, Page: 119 / 122

Search results

Summary of Contents for TUBE-ICE 03TA

Reviews: