P24A & P34A Service Manual
INSTALLING YOUR TUBE-ICE MACHINE
12/20/12
3-18
Auxiliary Controls or Equipment.
When connecting other equipment such as tower fan,
condenser pump, conveyor motors, bin level control, etc., refer to the control panel wiring drawing
for the proper connecting terminals and instructions. See Figure 6-3.
! IMPORTANT !
Be sure to follow the wiring schematic when incorporating overloads of
conveyor, fan, or pump motor starters (i.e., 5 MOL, 6 MOL, 7 MOL). Also
remove jumpers as instructed. This is necessary to provide proper
protection for the Tube-Ice
machine and its component parts.
! IMPORTANT !
Installation Review: A Checklist.
Make a visual check to be sure these steps have been taken
BEFORE continuing.
CHECK: _____ PRIOR TO OPENING VALVES, check all joints for leaks which may have
developed during shipment. (NOTE: the machine was shipped with a positive pressure of 20-25
PSIG, which should be indicated on the suction and discharge gages.)
CHECK: _____ All water supply and drain connections for conformity to requirements stipulated in
this manual and properly connected to inlets and outlets.
CHECK: _____ Electrical supply for proper size of fuses and for compliance to local and national
codes. See the machine nameplate for minimum circuit ampacity and maximum fuse size.
CHECK: _____ All field installed equipment (augers, conveyors, cooling towers, bin level controls,
etc.) for proper installation.
CHECK: _____ The applicable portion of the warranty registration/start-up report for proper
completion.
CHECK: _____ Cutter gear reducer oil level oil should run out of side pipe plug when removed.
CHECK: _____ The water distributors at top of freezer to make sure they are all in position (one
seated firmly in each tube with a vent tube in each distributor).
! CAUTION !
The crankcase heater should be energized for a minimum of
four hours and the oil temperature should be 100-110
°
°
°
°
F
before attempting to start the compressor.
! CAUTION
Summary of Contents for TUBE-ICE P-24A
