VNS Therapy SENTIVA M2000 Wand Technical Manual Download Page 48 | Manualshive

Page: 48 / 81

background image

48

CAUTION:

Battery depletion can occur between office visits. Therefore, LivaNova
recommends that epilepsy patients with magnet activation enabled
should perform a daily magnet activation to check stimulation.
If stimulation is not felt, instruct the patient to consult with the physician
to perform diagnostics testing.

All previously completed Diagnostics tests are listed in the history table on
the Diagnostics screen. Use the drop down menus to filter the reports by
type and/or date. Select any test to view details.

The System Diagnostics test assesses the electrical continuity between
the generator and the bipolar lead when connected. The test measures
the generator’s ability to deliver programmed output current and the lead
impedance status. You can perform this test on all generators supported by
the Programming System during implantation and patient follow-up visits.
A successful System Diagnostics during surgery or post-implant shows that
both the generator and lead are working properly. LivaNova recommends you
perform a System Diagnostics test before other diagnostic tests.

The Magnet Mode Diagnostics test will let you know if the generator is able
to deliver the programmed magnet output current. To perform this test do
the following:

1.

Select

TEST MAGNET

2.

Quickly pass the magnet over the generator (no more than 2 seconds)

3.

Place the wand over the generator and use the on-screen button to

start the test.

If you do not successfully activate magnet stimulation, a message will
display on the screen indicating the magnet presence was not detected.
Pass the magnet over the generator again and restart the test.

NOTE:

A System Diagnostics is performed for Model 1000 during the initial
interrogation, regardless of the type of interrogation (Advanced or
Rapid). The results are displayed on the Summary Screen and logged
as part of Diagnostics history. To perform a diagnostic test for a Model
1000 after the initial interrogation you can manually perform a System
Diagnostic test while in session.

System Diagnostics

Magnet Mode Diagnostics

«
...
46
47
48
49
50
...
»

Summary of Contents for SENTIVA M2000 Wand


















































































Reviews:

No comments

Related manuals for SENTIVA M2000 Wand

Brand: THORLABS Pages: 44

Brand: Tascam Pages: 8

Brand: B-K lighting Pages: 5

Brand: B-K lighting Pages: 4

Brand: B-K lighting Pages: 3

Sonopuls HD 4050

Brand: BANDELIN Pages: 48

Brand: Major tech Pages: 12

Brand: Qlight Pages: 4

Brand: Ultrawave Pages: 30

Brand: Ultrasound Technologies Pages: 12

Brand: ProLights Pages: 28

Brand: Numark Pages: 11

MT765 Challenger

Brand: Fast Pages: 31

Brand: REED Pages: 12

ResQCRP ResQPUMP ACD-CPR

Brand: Advanced Circulatory Pages: 2

Big Wheel RN1 Series

Brand: Osborne Pages: 8

Brand: Garmat Pages: 13

Brand: Gama Sonic Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands