Vivotek SD9363-EHL User Manual Download Page 225

Page: 225 / 332

VIVOTEK

225 - User's Manual

videoin_nresolution

0/7

This equals
"capability_videoin_c0_nresolution".

* This is kept for compatibility.

videoin_resolution

A list of <WxH>

0/7

This equals
"capability_videoin_c0_resolution".

* This is kept for compatibility.

videoin_maxframerate

A list of <Integer>

0/7

This equals
"capability_videoin_c0_maxframerate".

* This is kept for compatibility.

videoin_mjpeg_maxframe
rate

A list of <Integer>
and "-"

0/7

This equals
"capability_videoin_c0_mjpeg_maxframerate
".

* This is kept for compatibility.

videoin_h264_maxframer
ate

A list of <Integer>
and "-"

0/7

This equals
"capability_videoin_c0_h264_maxframerate".

* This is kept for compatibility.

videoin_codec

mjpeg, h264, h265
<product
dependent>

0/7

Available codec of a device, split by comma.
The sequence is not limited.

EX:
FD8183 supports H.264 and MJPEG, then this
is "mjpeg,h264".
IP9171 supports H.264, MJPEG and H.265,
then this is "mjpeg,h264,h265"

videoin_streamcodec

A list of <Positive
Integer>

0/7

This equals
"capability_videoin_c0_streamcodec".

* This is kept for compatibility.

videoin_flexiblebitrate

0/7

Indicate whether to support
flexible bit rate control.

videoout_codec

-, ntsc, pal

0/7

Current output information about video out.
1st element for 1st video-out, 2nd element for
2nd video-out, and so on. The number of
element depends on "capability_nvideooout".
"-": Video-out is not available

Summary of Contents for SD9363-EHL













































































































































































































































































































































Search results

Summary of Contents for SD9363-EHL

Reviews:

Related manuals for SD9363-EHL

Brands by name

Popular brands

Vivotek SD9363-EHL, User Manual

Search results

Summary of Contents for SD9363-EHL

Reviews:

Related manuals for SD9363-EHL

Brands by name

Popular brands